If you do not have an electrical outlet then a power cord will not be needed and the power supply can be connected directly to the dishwasher. In this regard, do dishwashers need a power cord?ĭishwashers do NOT come with power cords. Unscrew the wire nuts and pull apart the wires. Use a voltage meter to test the wires at the dishwasher to ensure the power is still off. How do you disconnect a dishwasher power cord? Take off the front cover at the bottom of the dishwasher to expose the wiring. GPFCORD (WX09X70910) can be installed on built-in GE, GE Cafe™ Series, GE Profile™ Series, Monogram and Hotpoint dishwashers. Be sure wires are not pinched under the cover.įurthermore, do GE dishwashers come with power cords?ĭishwasher Power Cord. Use UL listed wire nuts of appropriate size. You and into the ground.Connect incoming power cord white (or ribbed) to dishwasher white, black (or smooth) to black and ground to dishwasher green wire. You not to do that?) the current would flow into your finger, through To stick your finger in the socket this time (didn't we already tell If the switch is off, the light would be off. Wire (neutral), then it would flow to the light socket then out to the
What if the plug was misfired and current flowed in through the other It never gets to the socket and thus does not get to you. You should not get a shock, because the switch has interrupted the flow (you shouldn't, didn't your mother teach you that?) Switch is off, and you were to stick your finger into the light socket One wire connects to the switch, a wire connects the switch to the socket and then a wire from the socket returns to the other prong in the plug.Įlectricity should flow in through the hot wire to the switch. Consider a lamp the wiring is as follows. Here is an example of why it may matter which wire is connected to which prong in the plug. So that when the screw is tightened it will draw the wire in rather Make a small loop and place it clockwise under the screw terminal To the wide blade prong and the ground wire the rounded blade prong. If the wires are stranded, twist the strands.Ĭonnect the hot wire to the narrow blade prong, the neutral wire Using wire strippers, strip of roughly 1/2 inch of insulation to Excess wire may make reassemblyĭifficult or may result in wires that protrude from plug. Once you have the plug semi-assembled, cut off any excess Slip the wires through the back of the plug and pull them through The hot wire should be the switched wire. You can also test the device with ohm meter to find which wire connects
With the old plug and follow the wire that leads to the narrow prong. Which wire is which, refer to the old plug. The wires are color coded, in the U.S., white is typically neutral,īlack or red is hot and green is ground. The wide prong isĪlways neutral and so the neutral lead should be connected to it. The hot lead to the narrow prong on the new plug. Safety of the device may be compromised if you fail to properly match While the device may operate no matter which one you connect, the Wires from the power cord to the proper connectors in the new plug. Prong, then you must match the hot, neutral and ground (if present) If the old plug has different size prongs (aka blades) or a grounding In size, then you may connect either wire to the connectors in the Inspect the old plug, if it has two prongs and they are identical Take the end of the power cord and separate the wires so that each Tail left on the plug so that you can identify which wires were joined. To identify each wire, make a mark on the power cord and on the small If the power cord does not have color coding or other markings Also, cut off any damaged section of the powerĬord. If the plug is still attached, cut it off leaving only an inch or
Discharge these devices before beginning work. Some devices, including TVs and microwave ovens, can store a charge of electricity even when unplugged. Always use insulated tools for added safety. Always unplug the device before beginning work. If the power cord itself is damaged, the damaged section should be cut off or the entire cord should be replaced.Ĭaution: Please read our safety information before attempting any installation or repair.Įlectrical work requires safe practices. Do not replace an ungrounded plug with a grounded plug, nor should you replace a ground plug with an ungrounded one. When replacing a plug, be sure to select a replacement that is the same as the one being replaced and with the same rating. It is fairly easy to replace and should only take a few minutes. Occasionally the plug on a lamp cord or some other device will become damaged.
HOW TO REPLACE A DISHWASHER POWER CORD HOW TO
How To Replace a Plug on a Damaged Power Cord
0 kommentar(er)
